Are CD-Rs identical to normal CDs?

CDs are made by being pressed from a mold, while CD-Rs and CD-RWs are made by burning the information to the disc with a laser. Though they are not physically identical, they work just the same. However, you cannot record to pressed CDs, only to CD-R/RW discs. CD-R media is classified by its organic dye composition and the reflective layer. There are 4 kinds of dyes in use today: 1. Cyanine dye, which has a cyan blue color; 2. Phthalocyanine dye, which has a light aqua color; 3. Metalized azo dye, which has a dark blue color; 4. Formazan dye, which has a light green color. The reflective layer is a layer made up of either a silver alloy or 24K gold. There are different types of media mainly because each manufacturer configured their own materials and processes which all had to be patented. Each new CD-R manufacturer has to develop their own combination of materials. Recording Speed is the time it takes for a CD-R writer to write or burn the information to a CD-R disc. Currently, 52X is the preferred choice of speed in the industry. 52X means it takes 52 times as fast to write the information to the disc. For example, an 80-minute recording would take 80 minutes at 1X, 20 minutes at 4X, 5 minutes at 16X, 2.5 minutes at 32X, and 1.6 minutes at 52X. These times are general and do no account for lead in and lead out times, but they are a good rule of thumb. Pressing is the act of stamping out CDs at a replication house. These discs are created with a glass master, and then the CD is stamped or pressed out with the information already on the disc. Burning is the act of burning the information to the disc in a CD-R writer or burner. The visual difference between pressed and burned CDs is that pressed have the silver bottom that is all one shade. An example would be any CD you have purchased at a store, they were pressed. A burned CD-R has a change in shade on the bottom between the burned and unburned sections. Usually, the bottoms are blue or gold. Within a CD writer, a laser focuses on the blank CD-R and begins the process by actually burning pits into the reflective layer. In this process, what is created is a series of lands and pits within the reflective dye. The information is stored on the lands in a series of number combinations. These numbers are always 0s and 1s. The different combination of 0s and 1s on the lands make up the information on the disc that CD reader or player will read when the disc is played back. There are many factors that differentiate good quality CD-R media from poor quality media. One factor is the flatness of the disc. You want to know that your media is the flattest in the industry. Another factor is equal weight distribution around the disc. A disc that is uneven in weight will wobble while it spins in the burner and the reader. That will make for a poorly burned disc. Another factor is amount and consistency of the dye on the bottom of the disc. If the CD-R has too much or too little dye, the burning process will be affected and consequently, so will the reading process. These guidelines are key in determining the quality of a CD-R disc. The answer to this question depends on 2 factors; what is the quality of the CD-R writer and what is the quality of the CD-R disc. Assuming you have a professional CD-R writer and the media you are using is professional quality, there is no difference between pressed CDs and burned CD-Rs. This will vary depending on the burn speed. The CD-Rs that say For Music Use Only are meant to be used with the consumer stand-alone audio CD recorders from your local superstore. They cost a little more than data CD-Rs because a portion of that cost goes to the record industry. These disc also have copy protection per-written to them to discourage duplication. Data discs are written with a computer burner, not a consumer audio CD recorder. They are duplicatable and you can record audio or data to these discs. In the professional world, data CD-Rs are preferred over music only discs. If you are using professional quality CD-R media in a professional writer, there will be less of a chance of degradation and failure. In truth, the faster you burn a disc; the quality of the copy is lessened from the original. However, this will be noticed more with poor media than professional media. In regards to audio recording, the main question is, will I hear an audible difference? The answer to that is probably not, assuming your media and writer are professional quality. Ultimately, you want to use the media that gives you the best end result. One factor to look at is what the max recording speed is of the disc. If you try to burn it faster than it can handle, you will be left with a shiny coaster. If you are recording audio, you want to stay away from CD-RW discs. Besides the fact they are more expensive than regular CD-Rs, they don’t play audio in many CD players. Also, the CD-RW standard has its drawbacks. In actuality, CD-RW media can only be written to around 5 times before the disc is useless. Plus, you don’t want to be erasing and recording new material to the same disc over and over. It is cheaper just to buy once-write CD-R media and always have a backup copy. The age of an unwritten disc can be anywhere from 6 weeks to 100 years. Different manufacturers have different life spans. Taiyo Yuden media has a life span of 100 years. This is a good factor in determining which media is best for you. However, you probably won’t using CDs in 100 years, but the fact that they will last that long adds to credibility and quality. This life span is also assuming the CD-R is kept in a safe and cool environment. Exposure to excessive heat, humidity, or direct sunlight will reduce their life span. CD-R discs come in two storage sizes. The first is 650 MB or 74 minutes. The second is 700 MB or 80 minutes. Depending on the project, you can measure it in file size or length of time. It is not bad for the disc if you are careful. The wrong kind of ink or label can damage the disc. The adhesives from the label or the ink from a pen can dissolve the protective layer of the disc. The safest way to use labels with a CD-R is to purchase printable discs, which come per-made with labels. As for pens, you never want to use a ballpoint pen on the surface of a CD. There are many CD Safe pens and markers on the market. One safe way to write on the disc is to use a felt-tipped pen or marker. Never use a solvent-based pen on a CD-R. Unbranded CD-R media does not have a discernible brand name or logo on the disc. An example if this would be a plain, silver lacquer surface disc. Branded media does have a logo or brand name visible on the disc. Most media purchased at a superstore fits into this category. Printable media is a CD-R with a surface designed for ink jet printing directly onto the disc. In this case, you’ll need to get a CD printer, like the Micro-boards PF2 or DX2 publisher. These are gravity fed belt driven ink jet printers that allow for printing directly onto the disc. Besides the fact that a pressed CD is made differently than a CD-R, the difference would be in the change of color on the bottom of the disc. A pressed CD has the same shade of silver all the way across. A CD-R will have a change in shade between the burned and unburned sections. If the CD-R was burned to capacity, there is no real way to visibly tell the difference between the two discs.